Skip to main content

Recommended Painters

Knowing what a waterproofing contractor actually does on site helps you judge a quote, ask the right questions, and recognise whether the work has been completed properly before any tiles or finishes go over the top. Recommended Painters WA has more than 25 years of hands on experience in painting and surface solutions across Perth, and surface preparation is central to how we think about every coating job.

Why surface preparation decides whether waterproofing lasts

The membrane or coating applied to a wall or floor is only as good as what sits underneath it. Surfaces that carry old coatings, grease, loose render or efflorescence will not bond reliably to a new waterproofing product, no matter how good that product is. Skipping preparation is a common reason waterproofing fails early, and stripping back a failed membrane and redoing the work usually costs more than doing the preparation properly the first time.

For horizontal surfaces such as balconies, patios or concrete floors, preparation can include mechanical grinding to open concrete pores and create a surface profile that a coating can grip. For walls, the process typically involves wire brushing, pressure washing or sanding to remove anything that would compromise adhesion. Cracks, holes or damaged render are generally filled and allowed to cure before the first coat goes on. Recommended Painters WA treats surface preparation as an important part of achieving a quality, lasting finish, and our floor grinding and surface preparation service exists for this reason.

What does a waterproofing job actually involve on site?

A typical waterproofing application moves through site assessment, surface preparation, primer application, and then the membrane or coating itself, with checks between each stage.

The site assessment comes first. Recommended Painters WA assesses the condition of the surface, existing coatings and visible signs of deterioration before discussing an appropriate waterproofing solution. In general, a contractor also looks at drainage points, joints and penetrations such as pipes or fixings. These are the places where water most commonly finds a way through, so they need individual attention rather than a broad coat applied over the top.

After preparation, a primer is usually applied to improve adhesion between the substrate and the membrane. Primer selection depends on the surface: concrete, masonry, fibre cement sheet and timber each have different absorption rates and call for different formulations. Applying the wrong primer, or skipping it, can shorten the life of the membrane.

The membrane is then applied in the number of coats the chosen product specifies, with the applicator following the manufacturer’s instructions for each stage.

Common surfaces that need waterproofing in Perth properties

Recommended Painters WA provides waterproofing for bathroom and wet areas, balconies and external areas, and roofs, as well as recoating of existing waterproofing systems that may have deteriorated. Each location presents different challenges.

  • Bathrooms and wet areas: Sheet membranes or liquid applied systems are generally installed behind tiles and around shower recess perimeters, floor wastes and pipe penetrations. The work depends on the substrate condition, the intended application and compatibility with the proposed system.
  • Balconies and external areas: These surfaces combine foot traffic with full weather exposure. A flexible membrane is generally needed to accommodate minor movement without cracking, and drainage fall is usually checked so water moves away from the building rather than pooling.
  • Roofs: Roof waterproofing and protective coatings depend on the existing roof material, its condition and the requirements of the proposed system. Preparation commonly includes removing loose material and treating rust on metal sections before coating.
  • Recoating existing systems: Where a waterproofing system has deteriorated, the scope depends on the condition of the substrate, the compatibility of existing materials and whether repairs are needed before recoating.

Detail work around joins and penetrations

Flat, open surfaces are the straightforward part of any waterproofing job. The critical work happens at junctions: where a wall meets a floor, where a pipe passes through a membrane, where two sheets of substrate join, or where a balcony meets a door threshold.

At these points, a careful applicator installs reinforcing mesh or fabric tape bedded into the first coat of membrane before further coats go over the top. This reinforcing layer bridges minor movement and helps prevent the membrane splitting at a stress point. Without it, normal building movement can open a crack at the junction and let water in. Perth’s warm climate means thermal expansion and contraction can be a factor, particularly on metal framed or metal roofed structures.

Pipe penetrations are generally treated individually: the membrane is turned up around the pipe, a compatible sealant is applied, and the coat is feathered back onto the surrounding surface. Painting over a pipe penetration without that detail work leaves an obvious weak point.

How curing conditions affect the finished result

Waterproofing products are formulated to cure within a defined temperature and humidity range. Applying a membrane in direct summer sun when the substrate is very hot can cause the product to skin over too quickly, trapping solvent beneath the surface or reducing film thickness. Applying in cold or damp conditions, on the other hand, can extend cure times considerably.

As a general industry principle, a membrane should not be applied when rain is expected before the product has cured, and applicators should follow the product data sheet for the system being used. Weather matters most for exposed work such as roofs and balconies, while sheltered areas are less affected by conditions on the day.

How to tell if waterproofing has been applied properly

You do not need to be a tradesperson to spot signs of a careful application. Uniform colour and sheen across the coated area, with no thin spots, bubbles or missed sections, suggests consistent coverage. Reinforcing fabric should be visible at corners and junctions if you look before tiles or finishes are installed. The membrane should finish cleanly at a consistent height on walls, not fade out wherever the applicator’s arm reached comfortably.

On balconies and flat roofs, standing water should not remain long after rain if drainage fall was confirmed before coating. Persistent pooling suggests the fall was not checked or not corrected, and standing water will eventually find any weakness in the membrane.

For any Perth property where water damage is a concern, Recommended Painters WA provides waterproofing for homes and commercial sites. You can read about the surfaces and applications covered on the Perth waterproofing services page.

Frequently asked questions

Do I need to move out while waterproofing is being done?

It depends on the property and the job. Residential and commercial projects can involve different access, scheduling and preparation considerations, and commercial sites may need planning around ongoing operations. Ask about access requirements when you request a quote through the contact page.

How many coats of waterproofing are applied?

It depends on the product. Each system specifies its own primer and coat requirements, and some call for extra coats in high exposure areas or on porous substrates. The total thickness built up is what determines performance, and a single heavy coat does not behave the same as thinner coats built to the specified thickness.

Can waterproofing be applied over existing tiles?

It depends on the condition of the tiles and what the system is designed to bond to. Some systems adhere to a stable, sound tile surface; others require tiles to be removed so the substrate can be properly prepared. A membrane over loose, cracked or contaminated tiles is likely to suffer adhesion failure, so the existing surface should be assessed before an approach is recommended.

How long does waterproofing last?

Lifespan varies with the system used, how well the surface was prepared, the quality of the application, and the UV and weather exposure the surface receives. Exterior surfaces in Perth’s climate benefit from periodic inspection because UV degradation occurs over time. Because so many site conditions affect the result, a specific lifespan is hard to state before the surface has been assessed.

Is waterproofing the same as applying a waterproof paint?

No. Waterproof paints and sealers provide a degree of water resistance but are not the same as a dedicated membrane system. A membrane is designed to bridge small cracks, flex with the structure, and maintain an unbroken barrier under sustained water exposure. Waterproof paints can reduce moisture absorption on above ground masonry walls but are not suitable as the primary system in wet areas, balconies or roofs where water will pond or flow across the surface.

Related pages

This article draws on the following pages.

Stock photography by Pexels and our contributors.